suitcircle8

Reasons Your Fiat 500 Key Fob Won't Work A key fob from Fiat 500 is a convenient method to unlock the doors and get started the car. There are a myriad of reasons the fob could stop working. It could be due to a dead battery, damage to the receiver module, water issues, or interference. This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths in the automotive industry). This remote includes lock, unlock and trunk buttons. Dead Coin Battery A dead battery is the most common reason for your 500 key fob not working. Modern key fobs operate with a limited operating range, and should be within just a few feet of the car to operate. If you're far from your vehicle, and you press the key fob button, the car won't be able to respond, and will display the “Key Fob Not Detected” message in the instrument cluster. If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them in your local hardware store or online. After you've replaced the battery of your coin cell It is possible to test it by standing close to your Fiat 500 and pressing the buttons. The car should blink its parking lights, and the key fob should be able to operate the lock and unlock switches. If your key fob does not work after replacing the battery, it could be water damage that prevents it from connecting to the module inside your vehicle. Water damage can occur through a variety of methods, including an easy splash or submerging your key fob in saltwater at the beach. If you think your fob was exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, your fob may need to be reprogrammed by a professional locksmith or dealer. Water Damage Water damage can occur if you immerse the fob in the ocean, or wash it in a machine. Saltwater is especially dangerous to the fob's circuit board and can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an option however, if you drop it in the water in a cup or don't remember to remove it from your pocket before you run the washer and you don't have a chance, don't give in. First, remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Test the fob next to check if it's working. If the fob doesn't work, it might need to be changed. This is usually done by a professional or dealer auto locksmith. If your key is old and not programmed for your vehicle You will need to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith will have to cut the key to match the ignition in your vehicle. They will also need to reprogram the fob to your vehicle's system. This is a simple and cost-effective procedure that can be completed the same day. Receiver Module Issues The 500 key fob could not work because it's out of range. The remote usually has 30 feet of range or less, and if it's too far from your car, it won't respond to your commands. It is possible to solve this problem by moving the remote closer to your vehicle until it responds. If you've replaced the coin battery (commonly known as”button” or “button” or “watch”) and your fob doesn't function, it could have an internal circuit board problem. Reprogramming fiat 500 key fob replacement resolves the issue. You can find directions on how to do this for the majority of automobiles by searching YouTube or reading the owner's manual. It may be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension, it can prevent the battery from being properly seated and can cause the remote to malfunction. In rare instances, the fob could be out of connection with your vehicle as a result of hardware or software issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations it may be necessary to reinstall the program in your body control module, too. Interference In addition to a dead battery on a coin The key fob might not be receiving or transmitting an signal due to interference. This could occur if the key fob is near the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not work include a weak connection to the buttons and internal chip, or water damage. If the key fob failed to work one day in the middle of the night or after trying everything you can do at home to resolve it e.g. replacing the battery, reprogramming it and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets. Luckily, there is an easy way to reset all on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers. This could help get your key fob working again. If the problem persists you should seek out an experienced technician. They'll be able to determine the exact cause of your issues.